Choose your iMac model

If you're not sure which iMac you have, you can identify your iMac and then select it from the list below.

27-inch

24-inch

Your computer’s motherboard sports slots into which memory is plugged. What’s important is how those slots are filled with memory; you can’t just plug memory into the motherboard willy-nilly. Understand memory slot configuration There are several ways that a motherboard with four memory banks can host common amounts of memory: 1GB or 2GB. Because DIMMs. Normally, you fill Bank 1 first and then bank 2. If the RAM is mismatched then you want to Place matching pairs together If all RAM is the same brand and size, then it does not matter. If you have 2 4GB RAM cards and 1 8 GB Card then the two 4GB cards go in slots 0&1. And the single 8GB card goes in slot 2.

21.5-inch

• iMac (Retina 4K, 21.5-inch, 2019)*
• iMac (Retina 4K, 21.5-inch, 2017)*
• iMac (21.5-inch, 2017)*
• iMac (21.5 inch, Mid 2014)*
• iMac (21.5-inch, Late 2013)*
• iMac (21.5-inch, Late 2012)*

20-inch

17-inch

* Memory is not removable by users on iMac (21.5-inch, Late 2012), iMac (21.5-inch, Late 2013), iMac (21.5-inch, Mid 2014), iMac (21.5-inch, 2017), iMac (Retina 4K, 21.5-inch, 2017), and iMac (Retina 4K, 21.5-inch, 2019). If the memory in one of these computers needs repair service, contact an Apple Retail Store or Apple Authorized Service Provider. If you’d like to upgrade the memory in one of these models, an Apple Authorized Service Provider can help. Before you schedule an appointment, confirm that the specific Apple Authorized Service Provider offers memory upgrade services.

Memory in iMac (21.5-inch, Late 2015), and iMac (Retina 4K, 21.5-inch, Late 2015) is not upgradeable.

What Slot Does Ram Go Into The Sun

iMac (Retina 5K, 27-inch, 2020)

Get memory specifications for iMac (Retina 5K, 27-inch, 2020), then learn how to install memory in this model.

Memory specifications

This iMac model features Synchronous Dynamic Random-Access Memory (SDRAM) slots on the rear of the computer near the vents with these memory specifications:

For optimal memory performance, DIMMs should be the same capacity, speed, and vendor. Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

• PC4-21333
• Unbuffered
• Nonparity
• 260-pin
• 2666MHz DDR4 SDRAM

If you have mixed capacity DIMMs, see the install memory section for installation recommendations.

iMac (Retina 5K, 27-inch, 2019)

Get memory specifications for iMac (Retina 5K, 27-inch, 2019), then learn how to install memory in this model.

Memory specifications

This iMac model features Synchronous Dynamic Random-Access Memory (SDRAM) slots on the rear of the computer near the vents with these memory specifications:

Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

• PC4-21333
• Unbuffered
• Nonparity
• 260-pin
• 2666MHz DDR4 SDRAM

iMac (Retina 5K, 27-inch, 2017)

Get memory specifications for iMac (Retina 5K, 27-inch, 2017), then learn how to install memory in this model.

Memory specifications

This iMac model features Synchronous Dynamic Random-Access Memory (SDRAM) slots on the rear of the computer near the vents with these memory specifications:

Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

• PC4-2400 (19200)
• Unbuffered
• Nonparity
• 260-pin
• 2400MHz DDR4 SDRAM

iMac (Retina 5K, 27-inch, Late 2015)

Get memory specifications for iMac (Retina 5K, 27-inch, Late 2015), then learn how to install memory in this model.

Memory specifications

This iMac model features Synchronous Dynamic Random-Access Memory (SDRAM) slots on the rear of the computer near the vents with these memory specifications:

Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

• PC3-14900
• Unbuffered
• Nonparity
• 204-pin
• 1867MHz DDR3 SDRAM

For these 27-inch models

Get memory specifications for the following iMac models, then learn how to install memory in them:

• iMac (Retina 5K, 27-inch, Mid 2015)
• iMac (Retina 5K, 27-inch, Late 2014)
• iMac (27-inch, Late 2013)
• iMac (27-inch, Late 2012)

Memory specifications

These iMac models feature Synchronous Dynamic Random-Access Memory (SDRAM) slots on the rear of the computer near the vents with these memory specifications:

Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

• PC3-12800
• Unbuffered
• Nonparity
• 204-pin
• 1600MHz DDR3 SDRAM

Installing memory

The internal components of your iMac can be warm. If you've been using your iMac, wait ten minutes after shutting it down to let the internal components cool.

After you shut down your iMac and give it time to cool, follow these steps:

1. Disconnect the power cord and all other cables from your computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface to prevent scratching the display.
3. Hold the sides of the computer and slowly lay the computer face-down on the towel or cloth.
4. Open the memory compartment door by pressing the small grey button located just above the AC power port:
5. The memory compartment door will open as the button is pushed in. Remove the compartment door and set it aside:
6. A diagram on the underside of the compartment door shows the memory cage levers and the orientation of the DIMM. Locate the two levers on the right and left sides of the memory cage. Push the two levers outward to release the memory cage:
7. After the memory cage is released, pull the memory cage levers toward you, allowing access to each DIMM slot.
8. Remove a DIMM by pulling the module straight up and out. Note the location of the notch on the bottom of the DIMM. When reinstalling DIMMs, the notch must be oriented correctly or the DIMM won't fully insert:
9. Replace or install a DIMM by setting it down into the slot and pressing firmly until you feel the DIMM click into the slot. When you insert a DIMM, make sure to align the notch on the DIMM to the DIMM slot. Find your model below for specific installation instructions and notch locations:
   • iMac (Retina 5K, 27-inch, 2020) DIMMs have a notch on the bottom, slightly left of the middle. If your DIMMs are mixed in capacity, minimize the capacity difference between Channel A (slots 1 and 2) and Channel B (slots 3 and 4) when possible.
     
   • iMac (Retina 5K, 27-inch, 2019) DIMMs have a notch on the bottom, slightly left of the middle:
   • iMac (27-inch, Late 2012) and iMac (Retina 5K, 27-inch, 2017) DIMMs have a notch on the bottom left:
     
   • iMac (27-inch, Late 2013) and iMac (Retina 5K, 27-inch, Late 2014, Mid 2015, and Late 2015) DIMMs have a notch on the bottom right:
     
10. After you install all of your DIMMs, push both memory cage levers back into the housing until they lock into place:
    
11. Replace the memory compartment door. You don't need to press the compartment door release button when replacing the compartment door.
12. Place the computer in its upright position. Reconnect the power cord and all other cables to the computer, then start up the computer.
    

Your iMac performs a memory initialization procedure when you first turn it on after upgrading memory or rearranging DIMMs. This process can take 30 seconds or more, and the display of your iMac remains dark until it's finished. Make sure to let the memory initialization complete.

For these 27-inch and 21.5-inch models

Get memory specifications for the following iMac models, then learn how to install memory in them:

• iMac (27-inch, Mid 2011)
• iMac (21.5-inch, Mid 2011)
• iMac (27-inch, Mid 2010)
• iMac (21.5-inch, Mid 2010)
• iMac (27-inch, Late 2009)
• iMac (21.5-inch, Late 2009)

Memory specifications

Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

i5 and i7 Quad Core iMac computers come with both top memory slots populated. These computers will not start up if only a single DIMM is installed in any bottom slot; these computers should operate normally with a single DIMM installed in any top slot.

Core Duo iMac computers should operate normally with a single DIMM installed in any slot, top or bottom. ('Top' and 'bottom' slots refer to the orientation of the slots in the pictures below. 'Top' refers to the slots closest to the display; 'bottom' refers to the slots closest to the stand.)

Installing memory

The internal components of your iMac can be warm. If you've been using your iMac, wait ten minutes after shutting it down to let the internal components cool.

After you shut down your iMac and give it time to cool, follow these steps:

1. Disconnect the power cord and all other cables from your computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface to prevent scratching the display.
3. Hold the sides of the computer and slowly lay the computer face-down on the towel or cloth.
4. Using a Philips screwdriver, remove the RAM access door in the bottom of your computer:
   
5. Remove the access door and set it aside.
6. Untuck the tab in the memory compartment. If you're replacing a memory module, gently pull the tab to eject any installed memory module:
   
7. Insert your new or replacement SO-DIMM into the empty slot, noting the orientation of the keyway of the SO-DIMM as shown below.
8. After you insert it, press the DIMM up into the slot. There should be a slight click when you seat the memory correctly:
   
9. Tuck the tabs above the memory DIMMs, and reinstall the memory access door:
   
10. Place the computer in its upright position. Reconnect the power cord and all other cables to the computer, then start up the computer.

For these 24-inch and 20-inch models

Get memory specifications for the following iMac models, then learn how to install memory in them:

• iMac (24-inch, Early 2009)
• iMac (20-inch, Early 2009)
• iMac (24-inch, Early 2008)
• iMac (20-inch, Early 2008)
• iMac (24-inch Mid 2007)
• iMac (20-inch, Mid 2007)

Memory specifications

These iMac computers have two side-by-side Synchronous Dynamic Random-Access Memory (SDRAM) slots in the bottom of the computer.

The maximum amount of random-access memory (RAM) you can install in each computer is:

You can use a 1GB or 2GB RAM module in each slot for iMac (Mid 2007) and iMac (Early 2008). Use 1GB, 2GB, or 4GB modules in each slot for the iMac (Early 2009).

Use Small Outline Dual Inline Memory Modules (SO-DIMM) that meet all of these criteria:

DIMMs with any of the following features aren't supported:

• Registers or buffers
• PLLs
• Error-correcting code (ECC)
• Parity
• Extended data out (EDO) RAM

Installing memory

The internal components of your iMac can be warm. If you've been using your iMac, wait ten minutes after shutting it down to let the internal components cool.

After your iMac cools down, follow these steps:

1. Disconnect the power cord and all other cables from your computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface to prevent scratching the display.
3. Hold the sides of the computer and slowly lay the computer face-down on the towel or cloth.
4. Using a Philips screwdriver, remove the RAM access door in the bottom of the computer:
   
5. Remove the access door and set it aside.
6. Untuck the tab in the memory compartment. If you're replacing a memory module, untuck the tab and pull it to eject any installed memory module:
   
7. Insert your new or replacement RAM SO-DIMM into the empty slot, noting the orientation of the keyway of the SO-DIMM as shown above.
8. After you insert it, press the DIMM up into the slot. There should be a slight click when you seat the memory correctly.
9. Tuck the tabs above the memory DIMMs, and reinstall the memory access door:
   
10. Place the computer in its upright position. Reconnect the power cord and all other cables to the computer, then start up the computer.

For these 20-inch and 17-inch models

Get memory specifications for the following iMac models, then learn how to install memory in them:

• iMac (20-inch Late 2006)
• iMac (17-inch, Late 2006 CD)
• iMac (17-inch, Late 2006)
• iMac (17-inch, Mid 2006)
• iMac (20-inch, Early 2006)
• iMac (17-inch, Early 2006)

Memory specifications

For best performance, fill both memory slots, installing an equal memory module in each slot.
*iMac (Late 2006) uses a maximum of 3 GB of RAM.

Installing memory in the bottom slot

The internal components of your iMac can be warm. If you've been using your iMac, wait ten minutes after shutting it down to let the internal components cool.

After you shut down your iMac and give it time to cool, follow these steps:

1. Disconnect the power cord and all other cables from your computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface to prevent scratching the display.
3. Hold the sides of the computer and slowly lay the computer face-down on the towel or cloth.
4. Using a Phillips screwdriver, remove the RAM access door on the bottom of the iMac and set it aside:
   
5. Move the DIMM ejector clips to their fully open position:
   
6. Insert your RAM SO-DIMM into the bottom slot, keeping in mind the orientation of the keyed SO-DIMM:
   
7. After you insert it, press the DIMM up into the slot with your thumbs. Don't use the DIMM ejector clips to push in the DIMM, as this might damage the SDRAM DIMM. There should be a slight click when you seat the memory fully.
8. Close the ejector clips:
   
9. Reinstall the memory access door:
   
10. Place the computer in its upright position. Reconnect the power cord and all other cables to the computer, then start up the computer.

Replacing memory in the top slot

After you shut down your iMac and give it time to cool, follow these steps:

1. Disconnect the power cord and all other cables from your computer.
2. Place a soft, clean towel or cloth on the desk or other flat surface to prevent scratching the display.
3. Hold the sides of the computer and slowly lay the computer face-down on the towel or cloth.
4. Using a Phillips screwdriver, remove the RAM access door on the bottom of the iMac and set it aside:
   
5. Pull the two levers on each side of the memory compartment to eject the memory module that's already installed:
   
6. Remove the memory module from your iMac as shown below:
   
7. Insert your RAM SO-DIMM into the top slot, noting the orientation of the keyed SO-DIMM:
   
8. After you insert it, press the DIMM up into the slot with your thumbs. Don't use the DIMM ejector clips to push in the DIMM, as this might damage the SDRAM DIMM. There should be a slight click when you seat the memory fully.
9. Close the ejector clips:
   
10. Reinstall the memory access door:
    
11. Place the computer in its upright position. Reconnect the power cord and all other cables to the computer, then start up the computer.

If your iMac makes a tone after you install memory

iMac models introduced before 2017 might make a warning sound when you start up after installing or replacing memory:

• One tone, repeating every five seconds signals that no RAM is installed.
• Three successive tones, then a five-second pause (repeating) signals that RAM doesn't pass a data integrity check.

If you hear these tones, confirm that the memory you installed is compatible with your iMac and that it's installed correctly by reseating the memory. If your Mac continues to make the tone, contact Apple Support.

Confirm that your iMac recognizes its new memory

After you install memory, you should confirm that your iMac recognizes the new RAM by choosing Apple () menu > About This Mac.

The window that appears lists the total memory, including the amount of memory that originally came with the computer plus the newly added memory. If all the memory in the iMac has been replaced, it lists the new total of all installed RAM.

For detailed information about the memory installed in your iMac, click System Report. Then choose Memory under the Hardware section in the left side of System Information.

If your computer doesn't recognize the memory or doesn't start up correctly, confirm that the RAM you installed is compatible with your iMac and that it's installed correctly by reseating the memory. If you continue to have issues with the memory in your iMac, contact Apple Support.

If you are installing a RAM (memory) upgrade in your computer, or you are considering it, the following tips and information may help.

Memory buying tips

If you haven't purchased the memory yet, refer to our tips to finding the right RAM for your computer.

• Computer memory buying tips.

Before getting started

If you've purchased the RAM and you're ready to install it, run down this checklist before beginning the installation.

1. Ensure you are familiar with ESD and its potential dangers.
2. When installing the memory, make sure the computer is off and unplugged.

Locate memory slots and install memory

Follow these steps to safely install RAM modules in your computer's motherboard.

DIMM (DRAM, SDRAM, and DDR) memory installation steps

When handling memory, hold it by the sides at each end of the module. Be careful not to bend, flex, or drop the memory while handling it. When pushing the memory into the computer, do not apply an excessive amount of pressure. Doing so could cause damage to the memory module, and the slots on the motherboard. Finally, when installing the memory, distribute the pressure evenly by pressing on both corners of the memory module.

Once the memory is purchased, locate the memory slots on the computer motherboard. If no memory slots are available on the computer, one or more memory modules must be removed before the memory can be installed.

If the computer has a small form factor, it may be difficult to access the memory slots. You may have to temporarily remove cables or expansion cards before you can access them easily. When disconnecting anything from the computer, make sure you can remember where each cable and card goes.

Each slot on a motherboard that supports a DIMM is a bank; therefore the computer works if one memory module is purchased.

Examine the memory module before installing it into the computer. At the bottom of the memory module, you should notice one or more notches at the bottom of the card. These notches look like those shown in the picture below.

Make sure that the notches match up with the memory slot you are installing the memory into. These notches allow the memory to be installed only in one direction. If the memory is incompatible, it will not physically match with the slot.

After verifying the notches and direction, the memory needs to be installed, move each memory slot tab out or away from the memory module. These tabs will snap into place as the memory module is installed.

What Slot Does Ram Go Into Computer

Once these tabs are moved out, gently and firmly push the memory module into the slot. As the memory module is being pushed, the two tabs should snap and hold the memory module into place.

After the memory is installed in the computer, plug the computer back in, and turn it back on. As the computer is booting, the memory should be automatically detected and set up. If you have any difficulties with the memory detected or set up, enter the BIOS setup, and verify the memory is correctly detected by the system.

RIMM memory installation steps

What makes RIMM memory modules different from DIMM memory modules is the C-RIMM memory module. This module allows the computer to have a continuous flow of data. When installing a new RIMM, remove the C-RIMM. This module is a small circuit board and has only a few or no chips on it.

When the C-RIMM module is removed, and the two tabs are in the outward position, push the RIMM memory module to a vertical or 90-degree angle. As the memory module is being pushed, the two tabs should snap and hold the memory module into place.

Notebook (laptop) memory installation steps

Before the memory can be installed into a notebook, the memory slots must be located. If you are unfamiliar with where these slots are located, below is a listing of possible locations:

1. On a compartment on the bottom of the laptop.
2. Under the keyboard.
3. In the computer.

If you cannot locate the slots after looking at each of the above recommendations, we recommend you contact the computer manufacturer for additional help and information.

Once the slots are located, the next step is to install the computer memory. Today, most laptops follow the same memory installation.

What Slot Does Ram Go Into One

Because laptops are thin compared to a desktop computer, the memory banks are horizontal with the laptop. The memory must be inserted at an angle (approximately 75 degrees). Once it's in the slot, press down on the memory to snap it into place. The memory should also lay horizontally with the computer.

SIMM memory installation steps

30 and 72-pin SIMM memory modules must occupy a bank. Computers that use 72-pin SIMMs have two sockets as one bank. Therefore, two memory modules of equal value must be installed in pairs, unless instructed otherwise by the computer or motherboard manufacturer.

The installation of most SIMM memory is the same. The memory is placed into the slot at a 75-degree angle and while still in the memory slot, moved to a vertical (90-degree) angle. As the memory module is moved to a vertical position, it should snap into place. When installed, ensure that both sides of the memory module are snapped into place. If a memory module is not installed properly, it could cause damage to the computer.

We recommend the larger memory modules be installed in the lowest available banks. For example, if the computer has two 4 MB memory modules and you're installing two 32 MB memory modules, place the 32 MB memory modules either in banks 0 and 1, or 1 and 2.

Some computer manufacturers may require SIMM modules be installed in a certain order. So, if your new computer memory installation does not work, consider switching the location of the memory.

Set memory in BIOS

Once the memory appears is installed into the computer, test it. Put the case back on the computer. Connect the keyboard, monitor, and power to the computer. Turn on the computer.

We recommend you do not connect the rest of the cables yet. If you experience problems, you may have to disconnect all the cables again.

As the computer is booting, enter the BIOS setup, verify that the memory is detected, and if necessary, adjust the settings to match your memory specifications. When verification and configuration is complete, save the settings, exit BIOS, and reboot the computer.

Troubleshooting

If you encounter any problems when installing the RAM, refer to our Computer memory help and support.

Additional information

What Slot Does Ram Go Into

• See our memory definition for further information and related links.